IP Address: 192.168.0.2 (cannot be the same as the first computer)
MAC MAKING AN FTP DISK SOFTWARE
Then click the gear menu (below the port/service list) and select "Duplicate Service." While this step is not required, doing it will create a new software interface for the same ethernet port (called "multihoming"), which you can configure with network settings for the new network while preserving any current ethernet settings.Ĭhange the "Configure" option to "Manually" for the duplicated port, and enter the following for the setup information: Now you must set up the OS X machine to be on the same network so the machines can see each other, so go to the "Network" system preferences in OS X and select the "Ethernet" port. With these settings, close the control panel and restart the system. Gateway/Router: 192.168.0.254 (not needed, but may be required so this will do) To do this, choose "manual" in the "Configure" option of the TCP/IP control panel and then providing the following basic IP setup information (other information can be left blank):
This can be done regardless of what other devices and servers are connected to the same switch. To avoid problems, the second option is to manually set up a small network between the computers. Keep in mind that you should only do this if you are not connected to a network that already has a DHCP server on it (such as most routers).
MAC MAKING AN FTP DISK MAC
With no other routers connected, your Mac running OS X should act as a DHCP server and lease an IP address to your older computer. To do this, go to the "Sharing" system preferences, select "Internet Sharing," ensure something besides "Ethernet" is selected as your source connection, and then check the "Ethernet" option in the list. After this is done, you may need to restart the system.įor your OS X machine, you can set the system to act as a router by enabling internet sharing over your computer's Ethernet port. Select "Ethernet" for the "Connect Via:" option, and then choose "Using DHCP" for the "Configure" option. To do this, go to the Apple menu in OS 8 or 9, go to "Control Panels", and then open the "TCP/IP" control panel. The D-Link DFE-690TXD card should work, though the specifications say the card requires a PowerPC processor, leaving out some earlier PowerBook models.Ĭonnect your system to your local network via DHCP if you have a router or other network administrative device. Unfortunately, finding a PCMCIA ethernet adaptor that will work in older laptops (PowerBook 190, 1400, 2400, etc) may be hard to find, but there are a few out there.
If you have a "crossover" ethernet cable you should be able to connect to the two ethernet ports directly however, while some ports support direct connection with both crossover and straight-through cables, older ones did not have automatic detection and switching features so this may not work. Connect both computers to your router, or to a common switch or hub.
If you have a computer with a built-in Ethernet port, either built-in or with a separate expansion card, you should be able to transfer files to the new system. (Note that the steps here can be used for current computers as well, but most should be able to work just fine with automatic network detection technologies such as Bonjour.) Therefore, if you have an older Mac with an ethernet card or built-in ethernet port, you should be able to get your files off of it. Apple's "Apple Filing Protocol" (AFP) in OS 8 and OS 9 should be able to connect with current computers, at least in one way or another. Luckily the protocols for TCP-based networking have not changed enough to prevent connectivity with older machines. The options for portables were about the same, with the exception of the Ethernet option, which was mainly built-in when Apple introduced PowerPC G3 based laptops (though some previous models such as the PowerBook 540 did have the older AAUI-15 ethernet option).
MAC MAKING AN FTP DISK SERIAL
As such the majority of transfer devices, including flash drives, CD/DVD drives, and external hard drives, will not work the the older machine.īefore Apple introduced USB and FireWire in Macs starting around 19, the standard connectivity for desktop Macs was a SCSI port, a serial connector, an ADB port, and an ethernet port (Yes, 10Base-T was FAST!). Thinking it's an easy task, you grab your nearest USB stick only to find the computer does not have any USB ports, or for that matter, any FireWire ports. Sometimes you may have an old Mac lying around that you would like to retrieve files from.
0 kommentar(er)
